Programming the CodeDodger® Wireless Keypad

Adobe PDF Logo Download PDF instructions for the CodeDodger
ENGLISH                 SPANISH                 FRENCH
 
             
              On-line Instructions:

Test Garage Door Opener                     Program 1 Door Opener
Reset/Clear Keypad                             Program 2-3 Door Openers
Set PIN on Keypad                              Troubleshooting
Mounting the Keypad                           Additional Assistance

TEST your Garage Door Opener

  • Enter your PIN.
  • Press the button with the arrow up / arrow down triangles.


RESET /CLEAR your keypad
        (Starting over, Forgot PIN or Changing PIN)

  • Press and hold the PROG button. Keep holding while you -
  • Press and hold the 6 button. Keep holding while you -
  • Press the key with the arrow up and arrown down triangles.


SET Your Wireless Keypad PIN

  • Press the following keys in this order: [3]  [5]  [7]  [PROG]
    - Red LED blinks -once per second.     
  • Enter your PIN (3 to 8 characters).
  • Press the [PROG] key again.
      -Red LED blinks - twice per second and turns off.

PROGRAMMING Door Opener(s):
  Before you begin be aware of the following: 
    For Convenience: Program your keypad BEFORE mounting.
    Program Failure: If programming fails at any point CLEAR/RESET your keypad. 
    Locate the [Learn Code] button and the [Learn Code] red LED indicator.

Programming ONE Door Opener

  • Press the [Learn Code] button once. - The red LED indicator will blink.
  • Enter your PIN.
  • Press the button with the arrow up / arrow down triangles
    -The Learn Code Indicator LED will stay on.
  • Press the button with the arrow up / arrow down triangles a second time. -The Learn Code Indicator LED will turn off.
  • Press the button with the arrow up / arrow down triangles a third time.
    -Garage Door should now move.


Programming 2 or 3 Door Openers

(All Door Openers will use the same PIN)

 Programming the Keypad

  1. Enter your PIN and press the [PROG] button.
       -Red LED blinks once per second.
  2. Press the [PROG] button a second time.
       -Red LED blinks twice per second.
  3. Press the total number of Doors you wish to control.
    (Press either [2] or [3])
  4. Press the [PROG] button a third time.
        - Red LED blnks several times and turns off.

Programming the Door Openers

  1. Decide which door will be Door #1, #2 and #3.
    -Learn Code Indicator LED (on opener) blinks.
  2. Enter your PIN and press the arrow up/ arrow down triangle button.
    -Learn Code Indicator LED continues to blink.
  3. Press the number you have picked for this Door Opener [1], [2], or [3].
    -Learn Code Indicator LED stays on.
  4. Press the arrow up/arrow down triangle button a second time.
    -Learn Code Indicator LED turns off.
  5. Pressthe arrow up/arrow down triangle button a third time.
    -Door should move.

Repeat Steps 1 thru 5 for each door opener. Each door opener must be programmed to receive the signal from the wireless keypad.

TROUBLE SHOOTING: 

  • If the garage door does not move, check the red LED on the keypad.
  • If the LED is blinking rapidly, the PIN was entered incorrectly.
  • Any keypad button will control the door for 30 seconds after the door starts moving.
  • Rapid blinking of the LED indicates an error. After a few seconds the LED will turn off and then you can try again.
  • If the red LED does not blink during use, the battery needs to be changed.

Mounting Instructions

  • Remove battery cover.
  • Drill a 1/16" hole for the top mounting screw.
  • Install a screw into the top drilled hole, leaving a 1/8" gap between the screw head and the wall.
  • Hook the keypad over the screw.
  • Mark the bottom hole then screw in the bottom screw.
  • Reinstall the battery cover.

Additional Assistance:

Should you need additional information please contact our customer service department at
1-800-275-6187.