search button

 RapidSlat® Model 611  

  

Advanced Service Door - RapidSlat 611 Series 

The RapidSlat® Model 611 door is well suited for any application that requires a rolling steel door with the added benefits of high cycles, increased productivity and durability including banks, manufacturing facilities, and parking garages. It is ideal for customers in the parking garage market wanting to replace grilles. The fenestrated slats allow air circulation; they are more durable than grilles and more secure than fabric doors.

Max. standard width

up to 20' (6096 mm) depending on gauge and slat type 

Max. standard height

up to 20' (6096 mm) depending on gauge and slat type 

Mounting

Interior or exterior face of wall

Control panel

Variable frequency drive controller with self-diagnostics (time delay self-close timer and non-resettable cycle counter included); LCD readout, enclosure NEMA 4X rated

Curtain

Interlocking roll-formed slats, end locks attached to prevent lateral movement;
Curved profile type C-187 for doors up to 15'4" wide; 22 gauge galvanized steel;
Curved profile type C-275 for doors up to 20' wide; 22 gauge galvanized steel;
Flat profile type F-265 for doors up to 20' wide; 22 gauge galvanized steel;

Curtain finish

Gray, tan or white PowderGuardTM Premium powder coat with hardening additive

Bottom bar

Two PowderGuardTM Premium powder coated black angles (min. thickness 3/16”) with 2-wire, self-monitoring, fail safe, electric sensing edge

Hood

24 gauge galvanized steel primed, black painted

Brackets

Min. ¼” hot rolled primed, PowderGuardTM Premium powder coated black steel

Guides

Three structural steel angles
PowderGuardTM Premium powder coated black

Door roll

Direct driven, springless roll with integrated shafts; self-aligning grease-able sealed bearings; door does not require counterbalance device

Safety devices

Built-in drop stop device - patent pending design provides additional peace-of-mind against uncontrolled curtain travel in a high vehicular traffic area
Continously monitored sensing edge - all doors are equipped with a mandatory reversing or sensing edge to prevent entrapment
Photoelectric safety sensors with guards - provide additional safety during door operation to help prevent injury and damage

Operation

Direct drive hypoid gear motor/brake assembly (20” per sec up speed / 12” per sec down speed); drive assembly and limit sensors are factory pre-assembled; manual crank for power outage

Actuator

Single open/close/stop push button station incorporated into control panel

Wind load

20 psf when optional wear strips are not specified

Warranty

5 year limited warranty coverage on all mechanical door system components and control panel hardware.

  • Curved Profile type C-187 for doors up to 15’4” wide also available in: 20, 18 ga. galvanized steel; 22, 20 ga. stainless steel; 18 ga. (.040”) aluminum
  • Curved Profile type C-275 for doors up to 20’ wide also available in: 20, 18 ga. galvanized steel; 22, 20 ga. stainless steel; 16 gauge (.050”) aluminum
  • Flat Profile type F-265 for doors up to 20’ wide also available in: 20, 18 ga. galvanized steel; 22, 20 ga. stainless steel; 16 gauge (.050”) aluminum
  • Bottom Bar also available in: galvanized steel, stainless steel, aluminum
  • Guide options include galvanized steel, powdercoated steel and stainless steel
  • Hood also available in: powdercoat, stainless steel and aluminum. Sloped hood also available.
  • Brackets also available in: powdercoat; galvanized steel; stainless steel
  • Direct drive motors available in 1/2 HP, 1 HP, 2 HP, and 208/230/460 VAC 3-phase
  • Dual photoelectric sensors available for safety
  • Optional push buttons, loop detectors, radio control, motion detectors or any combination thereof available for door operation/control
  • PowderGuard™ Premium powdercoat finish with hardening additive available in up to 197 colors as well as color-matching to specification
  • For fenestrated service doors, provide slats with 3"x5/8" uniformly spaced openings (18 gauge C-275) (18 gauge F-265) the fenestrations can be open or with acrylic vision lites
  • For ventilated/perforated service doors, provide slats with 1/16" (16 mm) diameter perforations 3/32" (2.4mm) on center staggered rows (18 gauge C-275) (18 gauge F-265)